RK3588 Custom Android TV Board, WF-C3588-I1, AndroidSBC, Bergen

TL;DR: RK3588 Custom Android TV Board

Bergen, Norway - September 12, 2026. The 475th WF-C3588-I1 shipment left Shenzhen for Bergen this week with 36,465 units aboard, after a full burn-in cycle and a destination-market document check.

AndroidSBC manufacturer capacity statement from the WF-C3588 custom board production base serving Bergen, Norway. The line spans custom Android motherboards at the entry variant through core-board-plus-carrier work at the SOM end, all on the same Rockchip RK3588 silicon with 6 TOPS NPU, 8K H.265 decode and up to 32GB of LPDDR5. AndroidSBC ships the full range from the Wanlin Longgang plant, and Bergen buyers can mix custom variants inside a single framework agreement rather than opening a new supplier file for each product line.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group, a Shenzhen source-factory group that has spent more than a decade building custom OEM and ODM boards on Rockchip silicon. The line this release covers is the WF-C3588: nine custom motherboard variants built on the same Rockchip RK3588 octa-core 8nm platform with 6 TOPS NPU and 8K H.265 video, covering custom Android motherboards, custom industrial boards, core board and SOM carrier design, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards. Wanlin's Longgang plant in Shenzhen builds the WF-C3588 for Norway OEM, integrator and distributor programmes. For a Bergen buyer the practical value of the line is that one silicon and one supplier file cover nine custom categories.

WF-C3588-I1 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-I1 (Custom Industrial Motherboard for Fanless and Wide-Temperature Control) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Norway importers sourcing the WF-Series, the 8GB + 32GB (WF-C3588-I1-B) variant is the typical configuration for the custom industrial control and HMI programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Industrial Motherboard for Fanless and Wide-Temperature Control for Norway Buyers

Buyers in Bergen who have sourced a custom industrial motherboard for fanless and wide-temperature control for a few seasons tend to separate two questions: can the factory hold the price, and can it hold the allocation. The second one is harder. The Rockchip RK3588 is allocated at wafer level, and a 36,465-unit order placed against trader stock is the order most likely to slip a quarter without anyone warning the buyer. The second issue is firmware, not hardware. Vendors promise the full certified software stack and then ship a bare AOSP image, and the failure only surfaces at the warehouse when the unit is powered on against the customer's app.

The third exposure is paperwork. Factories that stamp marks without holding the underlying test reports leave the importer to produce a Technical File after the fact, which is exactly when the container is sitting in a bonded yard. AndroidSBC runs the custom board build, the certified image burn, the burn-in record and the certification file inside the Longgang plant, so the lot arrives complete rather than in pieces. The nine variants in the WF-C3588 cover industrial HMIs, panel PCs, PLC upgrades, SCADA nodes, DIN-rail controllers, factory automation, data acquisition, IIoT gateways, and machine control and each one carries three memory configurations, which keeps Bergen and Norway buyers on standard custom SKUs for most requirements.

The Norway paperwork question is settled before production. In Norway the market follows EEA rules rather than EU membership, and Nkom registration is required for radio equipment. The Longgang export desk prepares the destination-market file covering CE/EEA conformity with Nkom radio interface notification administered by Nkom and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), booking the lot into Port of Oslo on the Oslo to Rotterdam relay.

Competitive Comparison: WF-C3588-I1 vs Competing RK3588 Boards

The boards competing for the same socket in the custom industrial motherboard for fanless and wide-temperature control segment fall into three groups: off-the-shelf catalogue boards with no customization path, re-badged imports where the seller controls neither PCB nor firmware, and source-factory custom platforms with an engineering desk behind them. The WF-C3588-I1 sits in the third group and adds three things: Rockchip RK3588 silicon, an I/O and thermal profile that survives a continuous decode-and-NPU loop, and the per-lot certified image burn at Longgang.

• vs commercial boards in industrial dress: the WF-C3588-I1 is designed to -40C to 85C from the schematic up, not a consumer board with a bigger heatsink.
• vs local integrator bundles: the carrier design, the BSP port and the DIN-rail chassis all come from one Longgang engineering desk, so responsibility never splits across vendors.
• vs legacy PLC upgrade paths: the 6 TOPS NPU adds on-device vision and predictive maintenance to a PLC retrofit without a separate AI box.
• vs trading-company boards: the per-lot Technical File, the aging record and the EMC pre-compliance bench all live inside the source factory.

Global Custom Industrial Motherboard and Panel PC Market Trends

The Custom Industrial Motherboard and Panel PC market sets the pace for Bergen procurement this year, and it does not move on its own. The Edge AI hardware segment that MarketsandMarkets values at USD 26.9 billion in 2025, with a 32.7 percent CAGR reaching USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), sets the silicon allocation backdrop that custom RK3588 motherboard buyers also compete for. Three patterns stand out in the WF-C3588 order book for Norway:

• Industrial HMI panel: a machine builder replaces an aging Windows panel with a fanless HMI running a Yocto image and a custom UI.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-I1 board carries that headroom without a board change.
• SCADA edge node: a utility deploys DIN-rail controllers that aggregate substation data and push it over dual Gigabit links.

What the Custom Industrial Motherboard and Panel PC data does not show is the operational cost of a supply break, which is why Bergen buyers increasingly weight supplier continuity above a marginal price difference.

Read together, the three patterns explain the move in Bergen from spot quotes to framework agreements released monthly, which is what a custom RK3588 motherboard programme needs to hold a twelve-month shipping window without a mid-year break.

Partner Success Story: Halcyon Security Group in Bergen, Norway

Halcyon Security Group, a surveillance solutions provider serving the Norway market, deployed 10,200 custom WF-C3588-N6 NVR boards for a city surveillance programme. The rollout covered the industrial hmi panel, scada edge node, and factory automation cell workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 10,200 custom WF-C3588-N6 NVR boards for a city surveillance programme
• Region: Bergen, Norway
• Models used: WF-C3588-I1 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shanghai Yangshan with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Oslo via the Oslo to Rotterdam relay

"Sixteen channels of analytics on a fanless board ended our cloud subscription dependency overnight. The custom channel count and storage layout were factory options, not change-request theatre, and the certification file shipped with the lot."

- Tomas Berg, Engineering Director

Field Report: SMT line No.3 at the Wanlin Longgang plant, with operators loading Rockchip RK3588-based WF-C3588-I1 boards for the 36,465-unit order bound for Bergen

Reporter Pan Ze, on the ground in Bergen, Norway. Wanlin Longgang SMT line No.3 put the lot through three AOI passes and an X-ray inspection on every BGA package before it reached the burn-in rack. The WF-C3588-I1 boards then cleared 48 hours of thermal cycling between -20C and 70C with the decoder loaded against a stress stream. Final yield came in at 99.18 percent.

Radiated emissions on the sampled units came in below the internal limit with margin, which the compliance engineer noted as consistent with the last four lots.

The inspection confirmed three things on the spot: the WF-C3588-I1 units hold the burn-in with a yield above 99.18 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE/EEA conformity with Nkom radio interface notification administered by Nkom, cleared for entry at Port of Oslo on the Oslo to Rotterdam relay. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Norway importers can hand straight to their customs broker.

Filed by Pan Ze, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-I1 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-I1 (Custom Industrial Motherboard for Fanless and Wide-Temperature Control) as the lead SKU for Bergen and Norway programmes:

• Industrial HMI panel: a machine builder replaces an aging Windows panel with a fanless HMI running a Yocto image and a custom UI.
• PLC upgrade retrofit: a plant keeps the field wiring and swaps the controller for a CAN-equipped board with Modbus passthrough.
• SCADA edge node: a utility deploys DIN-rail controllers that aggregate substation data and push it over dual Gigabit links.
• Machine vision inspection: the 6 TOPS NPU runs defect classification at line speed on a 3.5-inch SBC inside the cabinet.
• Data acquisition gateway: a multi-serial variant logs sensor traffic from RS485 chains and buffers it during link loss.
• Factory automation cell: a systems integrator drives a robot cell and its safety stack from one wide-temperature board.
• Outdoor kiosk controller: an unattended terminal survives summer heat in a sealed enclosure with no fan to clog.
• Predictive maintenance: vibration and acoustic models run locally on the NPU and alarm before the PLC does.

Partnership Models for Bergen Buyers

Three commercial structures are open to Bergen buyers on the WF-C3588-I1 and the rest of the WF-C3588 custom variants:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

The three tiers share one factory, one test flow and one certification file. For Bergen buyers the standard entry point on the WF-C3588-I1 is the 8GB + 32GB (WF-C3588-I1-B) configuration at MOQ 5,000 units per shipment, 1-3 days to sample on standard variants and 15-30 days to mass production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Practically the layers that decide whether the board fits your product: the PCB layout and outline, the memory and storage fit (4GB to 32GB LPDDR4X/LPDDR5, eMMC to 128GB plus NVMe or SATA), the display interface mix (HDMI 2.1, DP 1.4, LVDS/eDP/MIPI), the I/O bank (CAN, RS232/RS485 multi-serial, relays, digital I/O), the wireless stack, and the enclosure or DIN-rail chassis. On top of that sit the firmware options: custom Android ROM with a locked launcher, custom Linux or Yocto image, pre-installed applications, custom boot animation and OTA updates. A Norway buyer can start from a standard WF-C3588 variant and change one layer, or bring a full schematic and have the carrier designed from scratch.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes. Under NDA, AndroidSBC delivers custom Android ROM work with proprietary services and a locked launcher, custom Linux images on Ubuntu, Debian, Yocto or Buildroot, BSP ports for customer carriers, and driver development for project-specific I/O. Source access is released to the partner, and the port is performed at Longgang, which matters because a vendor BSP rarely matches a custom carrier revision on the first try.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: The NPU is fully open on the custom line. Bring the model in PyTorch, ONNX, TensorFlow or Caffe and the Longgang desk handles the RKNN quantization, the runtime integration and the validation against your board's thermal and memory profile. Custom AI algorithm integration is a standard line item on the ODM scope, and the resulting model ships embedded in the firmware image burned per lot.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for Norway, and who handles them?

Answer: AndroidSBC handles them at the factory. Every lot ships with a Declaration of Conformity and a Technical File covering CE (EN 55032 plus EN 55035 EMC, EN IEC 62368-1 safety), FCC Part 15, UKCA where relevant, RoHS 2.0 and the REACH declaration, all dated within the prior twelve months. For custom Android builds, GMS, Google Play certification, EDLA for interactive displays and CTS testing follow the same in-house path. Where a Norway market needs an additional national mark, the export desk confirms coverage before the order is confirmed rather than after.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum supply, patches maintained across the firmware lines, OTA for firmware and NPU model updates. For a Norway programme running a custom board in the field, that commitment is written into the agreement at signature, which is what separates a source factory from a catalogue reseller.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes, including DDP into Amazon FBA in the US, EU and Japan, plus 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Cartons are labelled to FBA inbound spec and the declaration names Longgang as the origin. Partners who consolidate in Hong Kong usually take FOB Yantian and handle the last leg themselves.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-C3588 line, measured over the prior twelve months. On RMA, the partner returns the faulty WF-C3588-I1 unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record and the configuration file are attached per unit, the failure analysis normally comes back with a root cause rather than a credit note, which matters when a custom configuration is holding up a production line.

Contact AndroidSBC: Start Your WF-C3588-I1 Sourcing Conversation

The AndroidSBC export desk handles all WF-C3588 enquiries from Bergen and Norway. Direct factory contact on the WF-C3588-I1 and the rest of the custom industrial motherboard for fanless and wide-temperature control line is available through:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE/EEA conformity with Nkom radio interface notification for Norway, administered by Nkom, entering at Port of Oslo on the Oslo to Rotterdam relay
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

OEM and ODM enquiries move fastest when the first message carries the annual volume, the customization scope and the Incoterm. Send those three and the export desk replies with a per-lot quote and the full WF-C3588 MOQ matrix inside two business days.